CoMn@NC催化5-羟甲基糠醛常压氧化为2, 5-呋喃二甲酸二甲酯

Dimethyl furan-2, 5-dicarboxylate (DMFDCA) is a valuable biomass-derived chemical that is an ideal alternative to fossil-derived terephthalic acid as a monomer for polymers. The one-step oxidation of 5-hydroxymethylfurfural (HMF) to DMFDCA is of practical significance. It not only shortens the reaction pathway but also avoids the separation process of intermediates; thus, reducing cost. In this work, non-noble bimetallic catalysts supported on N-doped porous carbon (CoMn@NC) were synthesized via a one-step co-pyrolysis procedure using different pyrolysis temperatures and proportions of metal precursors and additives. We employed the prepared CoMn@NC catalysts in the aerobic oxidation of HMF under mild reaction conditions to obtain DMFDCA. High-yield DMFDCA was obtained by screening the prepared catalysts and optimizing the reaction conditions, including the strength and amount of the base, as well as the reaction temperature. The optimized yield of DMFDCA was 85% over the Co₃Mn₂@NC-800 catalyst after 12 h at 50 ℃ using ambient-pressure oxygen. The physicochemical properties of the catalysts were determined using a variety of characterization techniques, the factors affecting the performance of each catalyst were investigated, and the relationship between the physicochemical properties and performance of the prepared catalysts was elucidated. A porous structure with a high surface area had a positive effect on mass transfer efficiency. Cobalt nanoparticles (NPs) and atomically dispersed Mn were coordinated to N-doped carbon to form M―N_x (where M = Co or Mn). Based on the Mott-Schottky effect, there was significant electron transfer between each metal and the N-doped carbon, additionally, the metal NPs supplied electrons to the carbon atoms. The electron-deficient metal site in the pyridinic N-rich carbon was beneficial for the activation of HMF and oxygen. The activation of oxygen produced reactive oxygen species (such as superoxide radical anions) to ensure high selectivity to DMFDCA through dehydrogenative oxidation of the hemiacetal intermediate and hydroxymethyl group of 5-hydroxymethyl-2-methyl-furoate. The existence of disordered and defective carbons increased the number of active sites. Subsequently, we performed a series of control experiments. Based on our current experimental results and previous studies, we propose a simple mechanism for the aerobic oxidation of HMF to DMFDCA. The catalyst was stable, its performance decreased slightly after two cycles, and it was tolerant to SCN⁻ ions and resistant against N or S poisoning. Furthermore, the use of this catalytic system can be expanded to various substituted aromatic alcohols, such as benzyl alcohols with different substituents, furfuryl alcohol, and heterocyclic alcohols. Simultaneously, the product type was further extended from methyl esters to ethyl esters with a high yield when the substrate reacted with ethanol. In conclusion, this catalytic system can be applied in the production of carboxylic esters for polymers.     

锰离子氧化沉淀法实现锂离子电池LiNi0.8Co0.05Mn0.15O2材料的回收和利用

以浓盐酸为浸出剂,以NaOH和NH₄HCO₃为沉淀剂,利用Mn²⁺在碱性条件下的氧化反应改变离子的沉淀次序进而分步回收的方案,探究了浓盐酸酸浸处理三元正极材料LiNi_0.8Co_0.05Mn_0.15O₂的最佳条件。在分步沉淀过程中,Mn²⁺被氧化为不溶于非还原性酸的MnO （OH）₂,并在酸性条件下回收。Ni、Co则在碱性条件下利用NaOH回收,而Li则利用NH₄HCO₃回收。该方法中Mn的回收率达到85.1%,产品纯度达到98.6%; Li的回收率达到95.0%,产品纯度达到99.3%。由回收材料重新合成的三元正极组装的软包电池的首圈放电比容量达到了175 mAh·g^-1,可以以超过99.5%的库仑效率稳定循环50圈。     

A Photoelectrochemical Sensor for Firstly the Detection of Amlodipine Besylate Based on an MnC4Pc Coated ZnO Composite Materials

In this study, tetracarboxylic manganese phthalocyanine coated nano-zinc oxide (MnC₄Pc-ZnO) composite material was prepared by in-situ growth method and modified with indium tin oxide (ITO) glass electrode to construct a photoelectrochemical (PEC) sensor. A PEC sensor for the determination of amlodipine besylate (AB) was developed for the first time based on the principle of precipitation reaction between heavy metal ions and dihydropyridine and the recombination suppression effect of the material. The morphology and optical properties of the MnC₄Pc-ZnO composites were characterized by scanning electron microscopy (SEM) and ultraviolet-visible diffuse reflectance spectroscopy (UV-vis DRS). Chronoamperometry (i-t) and electrochemical impedance spectroscopy (EIS) were used to study the PEC behavior of ITO electrodes modified by MnC₄Pc-ZnO composite material. The study found that the MnC₄Pc-ZnO composite material has a good photocurrent response to AB, and there was a good linear relationship between the concentration range of 75 nM-250 μM, the linear equation was I(μA)=−5.2×10⁻⁸×lgC+3.2×10⁻⁸ (r=0.9947), a limit of detection (LOD) of 20 nM. In addition, MnC₄Pc-ZnO/ITO also has good selectivity and stability. The PEC sensor detects amlodipine besylate tablets, amlodipine besylate dispersible tablets, and biological samples, with standard addition recovery rates of 96.11 % and 103.96 %, respectively. The determination result has good accuracy, and the PEC sensor provides a new method for detecting AB.     

A Series of Low-Coordinate Iron Selenido Complexes: Reactivity of a Linear Iron(I) Silylamide towards Selenium

A variety of different low-coordinate iron selenide complexes is reported. These are obtained by reaction of the linear iron(I) silylamide K{18c6}[Fe(N(Dipp)SiMe₃)₂] (Dipp=2,6-diisopropylphenyl) with red selenium. Careful adjustment of the reaction conditions results in the formation of unique low-coordinate selenido iron complexes, namely a monoselenide bridged [2Fe−1Se]²⁺ complex, as well as mononuclear iron per- and triselenides. Further, C−H bond activation of one of the silylamide ligands by a putative terminal iron monoselenide is observed.     

电解水金属单原子催化剂的研究进展

氢能因其能量密度高、清洁无污染等特点,作为替代化石燃料的能源载体得到了广泛的研究.如何清洁高效地制备氢气受到了大量研究者的关注.当前,以化石能源的热反应所得副产氢气是主要来源.然而,采用该类方法不仅不能摆脱化石能源的使用以及温室气体的排放,还会造成生产氢气的纯度不高,碳氧化物杂质浓度过高的问题,严重影响氢气的后续使用.采用可再生能源(太阳能、风能等)所产富余电,进行电解水制氢,产生的氢气不含碳氧化合物杂质,纯度很高,可以真正实现碳的零排放,被认为是未来氢气来源的重要方式.目前,电解水制氢在制氢市场的所占份额较小,而造成这样局面的主要因素是该过程中的高能耗问题.为了降低能耗,开发高效催化剂加速两个电极上的电解反应的动力学尤为重要.近年,金属单原子催化剂(SACs)因其独特的结构,在很多研究中被用作电解水催化剂,进而开发出大量高性能的金属单原子电解水催化剂.本文综述了近年SACs在电解水催化方面的应用.首先,针对电解水反应本身,总结了阴阳极两侧的电极反应机制以及影响电极催化性能的关键吸附中间物种;然后,根据载体的不同,即合金、碳以及其它化合物将SACs分为三类,总结了相关电解水催化研究现状,并且针对不同类型SACs目前的发展情况,提出了它们各自存在的问题.其次,进一步总结了影响SACs电解水催化活性的因素,提出了四种决定SACs催化性能的影响因子,分别为金属原子的固有元素性质、配位环境、几何结构和负载量;同时讨论了这四类影响因素对SACs催化活性的影响机制,总结了调控各类影响因素的方法,为SACs的设计提出了一些建议.最后,展望了SACs在电解水催化中的应用,探讨了SACs在催化剂设计及催化机制研究方面的问题,提出了SACs在电解水催化中的未来发展方向.     

Expanding the Ligand Classes Used for Mn(II) Complexation: Oxa-aza Macrocycles Make the Difference

We report two macrocyclic ligands based on a 1,7-diaza-12-crown-4 platform functionalized with acetate (tO2DO2A²⁻) or piperidineacetamide (tO2DO2AM^Pip) pendant arms and a detailed characterization of the corresponding Mn(II) complexes. The X−ray structure of [Mn(tO2DO2A)(H₂O)]·2H₂O shows that the metal ion is coordinated by six donor atoms of the macrocyclic ligand and one water molecule, to result in seven-coordination. The Cu(II) analogue presents a distorted octahedral coordination environment. The protonation constants of the ligands and the stability constants of the complexes formed with Mn(II) and other biologically relevant metal ions (Mg(II), Ca(II), Cu(II) and Zn(II)) were determined using potentiometric titrations (I = 0.15 M NaCl, T = 25 °C). The conditional stabilities of Mn(II) complexes at pH 7.4 are comparable to those reported for the cyclen-based tDO2A²⁻ ligand. The dissociation of the Mn(II) chelates were investigated by evaluating the rate constants of metal exchange reactions with Cu(II) under acidic conditions (I = 0.15 M NaCl, T = 25 °C). Dissociation of the [Mn(tO2DO2A)(H₂O)] complex occurs through both proton− and metal−assisted pathways, while the [Mn(tO2DO2AM^Pip)(H₂O)] analogue dissociates through spontaneous and proton-assisted mechanisms. The Mn(II) complex of tO2DO2A²⁻ is remarkably inert with respect to its dissociation, while the amide analogue is significantly more labile. The presence of a water molecule coordinated to Mn(II) imparts relatively high relaxivities to the complexes. The parameters determining this key property were investigated using ¹⁷O NMR (Nuclear Magnetic Resonance) transverse relaxation rates and ¹H nuclear magnetic relaxation dispersion (NMRD) profiles.     

矿物元素指纹图谱的建立及在西洋参产地鉴别中的应用研究

采用电感耦合等离子体质谱法测定了山东、吉林、美国和加拿大4个产地西洋参中50种矿物元素的含量,研究了不同产地西洋参矿物元素的差别和转换系数,构建了西洋参的矿物元素指纹图谱。以各产地矿物元素含量的平均值构建了山东、吉林、美国和加拿大产西洋参的矿物元素标准指纹图谱。采用SPSS 20.0计算了各西洋参矿物元素指纹图谱与其矿物元素标准指纹图谱的相似度,确定了山东、吉林、美国和加拿大产西洋参矿物元素指纹图谱的相似度阈值分别为0.93、0.91、0.98和0.93。通过比较未知产地西洋参矿物元素指纹图谱与矿物元素标准指纹图谱的相似度,进行西洋参的产地判别。采用20批未知产地西洋参样品验证模型的准确性,正确率为85%。此外,研究表明,不同生长年限和不同部位西洋参样品对所建立的西洋参产地鉴别方法无影响。     

Application of Octanohydroxamic Acid for Salting out Liquid–Liquid Extraction of Materials for Energy Storage in Supercapacitors

The ability to achieve high areal capacitance for oxide-based supercapacitor electrodes with high active mass loadings is critical for practical applications. This paper reports the feasibility of the fabrication of Mn₃O₄-multiwalled carbon nanotube (MWCNT) composites by the new salting-out method, which allows direct particle transfer from an aqueous synthesis medium to a 2-propanol suspension for the fabrication of advanced Mn₃O₄-MWCNT electrodes for supercapacitors. The electrodes show enhanced capacitive performance at high active mass loading due to reduced particle agglomeration and enhanced mixing of the Mn₃O₄ particles and conductive MWCNT additives. The strategy is based on the multifunctional properties of octanohydroxamic acid, which is used as a capping and dispersing agent for Mn₃O₄ synthesis and an extractor for particle transfer to the electrode processing medium. Electrochemical studies show that high areal capacitance is achieved at low electrode resistance. The electrodes with an active mass of 40.1 mg cm⁻² show a capacitance of 4.3 F cm⁻² at a scan rate of 2 mV s⁻¹. Electron microscopy studies reveal changes in electrode microstructure during charge-discharge cycling, which can explain the increase in capacitance. The salting-out method is promising for the development of advanced nanocomposites for energy storage in supercapacitors.     

Prediction of an outcome using NETwork Clusters (NET-C)

Birth weight is a key consequence of environmental exposures and metabolic alterations and can influence lifelong health. While a number of methods have been used to examine associations of trace element (including essential nutrients and toxic metals) concentrations or metabolite concentrations with a health outcome, birth weight, studies evaluating how the coexistence of these factors impacts birth weight are extremely limited. Here, we present a novel algorithm NETwork Clusters (NET-C), to improve the prediction of outcome by considering the interactions of features in the network and then apply this method to predict birth weight by jointly modelling trace element and cord blood metabolite data. Specifically, by using trace element and/or metabolite subnetworks as groups, we apply group lasso to estimate birth weight. We conducted statistical simulation studies to examine how both sample size and correlations between grouped features and the outcome affect prediction performance. We showed that in terms of prediction error, our proposed method outperformed other methods such as (a) group lasso with groups defined by hierarchical clustering, (b) random forest regression and (c) neural networks. We applied our method to data ascertained as part of the New Hampshire Birth Cohort Study on trace elements, metabolites and birth outcomes, adjusting for other covariates such as maternal body mass index (BMI) and enrollment age. Our proposed method can be applied to a variety of similarly structured high-dimensional datasets to predict health outcomes.     

Aprotic Amine-modified Manganese Dioxide Catalysts for Selectivity-tunable Oxidation of Amines

Organic modifiers have shown promising potential for regulating the activity and selectivity of heterogeneous catalysts via tuning their surface properties. Despite the increasing application of organic modification technique in regulating the redox-acid catalysis of metal oxides, control of the acidity of metal oxide catalysts for enhanced reaction selectivity without sacrificing their redox activity remains a substantial challenge. Herein, we show the successful control of redox-acid catalysis of metal oxides with aprotic tertiary amine modifiers. Robust modification of manganese dioxide catalysts with N,N-dialkylcyclohexylamine selectively blocks the Lewis acid sites, with their redox activity mostly unaffected. This enables efficient synthesis of imines in high to excellent selectivity via aerobic oxidation of structurally diverse aryl amines.